JDIR-LCPA Series (+27dBm)

Quad Band Industrial Repeater - USA

Product Overview

The JDIR- LCPA Series Cellular Repeater is a high-powered, gain adjustable quad band repeater that is perfect for use in a DAS application needing to provide enhanced coverage for Voice, 3G and 4G high speed data to an office building, department store, warehouse, underground parking lot, or small multi-story hotel. Our repeaters are built with carrier level optimization in mind and thus use very high quality internal components to achieve this. These include low noise amplifiers with high linearity, properly specified  and set output power limits and well designed alarm/protection circuitry.

A main feature standard on all our repeaters are individually assigned Uplink and Downlink attenuation adjustment DIP switches. This is particularly advantageous when optimizing your repeater for LTE to ensure you get the best throughput speeds.  

A certified test report is included with each repeater that leaves our factory, so you are assured of strict quality controls.

  • Unlimited Call Capacity
  • Industry Leading Quad Band Repeater
  • 75dB Gain / 27dBm Output Power
  • 36 Months Warranty
  • 30 Day Money Back Guarantee
  • MUTE - Auto Shut Down if oscillation is detected
  • MGC: Manual Gain Control (Uplink & Downlink)
  • Automatic Limit Control Feature
  • Built-In High-speed Brushless Cooling Fan
  • Transparent when optimized
  • Coverage Area - (35,000 - 80,000 sq ft)
  • Supports 90-240 Volts
  • Alarm LED's for Error Detection
  • Supports Any Cellular Device (Voice & Data)
  • Automatic Gain Control Feature
  • Carrier Grade Performance & Quality
  • Free! - Phone Tech Support

SKU:

JDIR-LCPA-27
Quad Band - 700 / 800 / 1900 / 1721

Product Request

Write us a message

Vertical Tabs

Upload Background Image
Drop File

To maintain safe and specific output signal levels, this advanced repeater has built-in AGC (Automatic Gain Control) and ALC (Automatic Limit Control) circuits which can automatically control the gain of the repeater within a 15dB range depending on the RF environmental conditions. In addition, it also has built-in attenuation dip switches that allow you to manually attenuate (fine tune) the repeater's uplink and downlink channels in 1db increments up to 31dB, using color changing LED's as a status indicator. These Alarm LED's are used as a guide to prevent your installation from re-producing errors due to excessive input signal strength if a pre-amp is used, or from signal oscillation due to the indoor antenna and outdoor antenna being too close to each other, which can have adverse effects on a base station and greatly impede system performance. 

A Network Safe / MUTE™ feature comes standard with this repeater to protect the cellular network. In short, the repeater will stop transmitting if any errors or signal oscillation is detected within 2-4 sec of detection. It will cycle for 30 sec then attempt to transmit again. If no adjustment in gain has been made to correct the error within the 30 sec MUTE cycle, the system will again shut down after 5 sec. It will run this sequence for a total of 3 times and then shut down completely. Power cycling the unit will reset this sequence.

Due to the number of active amplifiers inside this repeater, a high-speed 3" brush-less fan is built into it in order to maintain cooler operating temps. This also greatly extends the lifespan of the repeater. 

This repeater is designed to be transparent to the network and will therefore support the same number of calls the serving sector of the BTS the donor antenna is aimed at. 

Frequency Chart

Model Uplink Downlink
JDIR-LCPA-27 LTE (A&B) 698 ~ 716 MHz 728 ~ 746 MHz
LTE (C) 776 ~ 787 MHz 746 ~ 757 MHz
CELL 824~849 MHz 869~894 MHz
PCS 1850~1910 MHz 1930~1990 MHz
AWS 1710-1755 MHz 2110-2155 MHz
 Filter Bandwidth Wideband
 Max total output power   ≥20dBm ≥27dBm
 Max. Gain ≥70dB ≥75dB
 Gain Flatness   700/800/1900: ≤6dB, 1721: ≤8dB 
 AGC Range ≧15dB - Auto shut off after 15dB (MUTE)
 Maximum Input Power   0dBm
 Gain Control Range (MGC) ≥31dB in step of 1dB by Dip Switch
 V.S.W.R ≤2
Intermodulation 9KHz~1GHz≤-36dBm 9KHz~1GHz≤-20dBm
1GHz~12.75GHz≤-30dBm 1GHz~12.75GHz≤-20dBm
Spurious Emission 9KHz~1GHz≤-36dBm
1GHz~12.75GHz≤-30dBm
LTE Meets 3GPP LTE Standard
LTE ≤ 12.5%
LTE ≤ -35dB @ Spreading Factor 256
CDMA ρ > 0.980
CDMA Meet IS95 & CDMA2000
PCS & AWS Meet 3GPP TS 25.143( V 6.2.0 )
PCS & AWS ≤ 12.5%
PCS & AWS ≤ -35dB @ Spreading Factor 256
Noise Figure (@ max gain)   ≤8dB
Group Delay ≤ 1.0μs
 Impedance   50Ω

Mechanical Chart

Power Supply Input 90- 264 VAC,50 Hz, transformer: 12V / 11A
Cooling Heatsink Convection Cooling & 3" Brushless Fan
Power Consumption < 35W
Operating Temperature -25°C~+55°C (-13F ~ 131F)
 RF Connector N Female
Weather Proof IP40
 Dimension 250 x 380 x 104 mm (9.84" x 14.96" x 4.09")
Weight ≤8Kg (17.6Lbs)
LED Alarm Standard
Power LED Power Indicator
ALC LED Amber @ ALC 1~5dB, Red @ ALC 15-20dB
LED off after 5 seconds red color
30 Day Money Back
GUARANTEE

36 Month Warranty

This is NOT a CONSUMER device
It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation.

Upload Background Image
Drop File

Contact one of our cellular signal enhancement engineers.

CONTACT US

Upload Background Image
Drop File